193 Cutting conditions / Schnittwertempfehlungen VHMAK Slot milling / Nutfräsen ap max. (mm) ae max. (mm) Fz (mm/tooth) < 0,03 < 0,03 0,005 - 0,009 < 0,04 < 0,04 0,007 - 0,012 < 0,05 < 0,05 0,009 - 0,015 < 0,06 < 0,06 0,011 - 0,018 < 0,08 < 0,08 0,013 - 0,021 < 0,10 < 0,10 0,016 - 0,025 < 0,12 < 0,12 0,020 - 0,030 < 0,15 < 0,15 0,030 - 0,040 < 0,20 < 0,20 0,035 - 0,050 < 0,25 < 0,25 0,040 - 0,060 < 0,30 < 0,30 0,050 - 0,075 Shoulder milling / Eckfräsen ap max. (mm) ae max. (mm) Fz (mm/tooth) < 0,3 < 0,03 0,005 - 0,009 < 0,4 < 0,04 0,007 - 0,012 < 0,5 < 0,05 0,009 - 0,015 < 0,6 < 0,06 0,011 - 0,018 < 0,8 < 0,08 0,013 - 0,021 < 1,0 < 0,10 0,016 - 0,025 < 1,2 < 0,12 0,020 - 0,030 < 1,5 < 0,15 0,030 - 0,040 < 2,0 < 0,20 0,035 - 0,050 < 2,5 < 0,25 0,040 - 0,060 < 3,0 < 0,30 0,050 - 0,075 Ød (mm) 0,3 0,4 0,5 0,6 0,8 1,0 1,2 1,5 2,0 2,5 3,0 • Cutting speed Vc is based on max. 50.000 rpm. Schnittgeschwindigkeit Vc bezogen auf max. 50.000 U/min. • End mills can be used also for drilling with reduced cutting conditions. Mit verringerten Schnittwerten können die Fräser auch für Herstellung von Bohrungen verwendet werden. Material group TSR Hardness (N/mm2) HB N5.1 < 500 < 150 N5.2 < 400 < 120 N5.3 < 350 < 100 N5.4 N5.5 Cutting speed Vc m/min 350 - 650 200 - 500 350 - 500 400 - 1000 400 - 1000 Coolant emulsion / air emulsion / air emulsion / air emulsion / air emulsion / air ap ae ap ae=Ød VHMAK 2 015 064 06 10 L080 Workpiece Material: Tungsten Copper Van Hoorn Competitor Ø 1,5 mm 1,5 mm V c 180 m/min 120 m/min n 38.200 rpm 25.500 rpm F z 0,021 0,015 Z 2 2 V f 1500 750 a p 0,02 mm 0,02 mm a e 0,02 mm 0,02 mm Coolant emulsion emulsion Q 0,0006 0,0003 Material removal rate Zerspanungsleistung 0,0006 0,0005 0,0004 0,0003 0,0002 0,0001 0 Van Hoorn Competitor
RkJQdWJsaXNoZXIy Nzg5MzM=